How To Patch Intex Pool Ring Easily

You’ve finally finished your excellent new in-ground pool. There’s just one little problem – the liner isn’t sticking! That’s because of the small hole you drilled into your liner to allow water to enter the pool. No worries, though; it’s super easy to fix.

 

Causes Of Leaks In Intex Pool Ring

Intex pools are made from plastic and can deteriorate over time. In particular, the seams in the pool ring can wear out and create leaks. Leaks are among the most common causes of pool ring failure. If you get a small crack in the polymer sealant, they’re probably leaking.

This is usually caused by hard use or extreme temperature changes. This is common in older models that have been left outside for extended periods. To prevent this, keep your pool covered with a cover, and don’t leave your pool outside for long periods.

Sealed pools may leak due to poor maintenance or improper installation. Leaks can also occur if dirt gets into the pool rings or if pieces of debris become lodged in the pump seals.

For these reasons, it’s important to check the seals regularly, clean your pool frequently and make sure there are no sharp edges or loose objects near the pool to avoid potential damage.

 

Finally, pressure build-up from surface tension can create a leak at the bottom of the pool ring. This is usually caused by letting water accumulate on one side before draining it out.

 

How To Patch Intex Pool Ring

Here’s how: Suppose you have an Intex in-ground pool, and the ring around the liner has become loose after a few uses. In that case, this article will explain how you can patch the gap between your liner and the base so that water can no longer seep out.

 

What you will need before you start: The first thing you will need is some weather-resistant adhesive caulk. The patching process may seem like a newbie DIY project, but trust us, it’s not complicated.

 

Here are the materials and tools that you will need: 

  • tube of caulkwith a diameter slightly more significant than your opening (like 3/4 inches)
  • drillwith a 1/8-inch bit
  • A screwdriver: Phillips or flathead preferable (you might also need pliers if yours is small)
  • An extension cord:You won’t be able to use an extension cord for power, but for a few DIY projects like this one, we recommend using one anyways.

 

Prep work

Before you start patching your liner, you will want to do a few things. First, you’ll need to ensure that your liner is clean and dust-free.

If there is any dust or dirt trapped in the liner, then it will stop the adhesive from sticking properly. So make sure you clean the liner’s surface with a brush or vacuum.

After that, you’ll want to remove the liner from your pool. It will make things easier, and you won’t have to remove the entire liner from the collection.

 

Install the patch

You are ready to install the patch if you’ve done everything correctly. First, you’ll want to use your drill to drill a small pilot hole in the center of the ring.

The process will ensure that the patch will stay in place and you won’t end up with a leak. Next, you’ll want to cut the patch to fit the hole.

Make sure to cut it small enough, so no excess will cause water to seep. Now, you’ll want to use your screwdriver to push the patch into place against the liner.

 

 

How To Care For An Intex Pool Ring

Proper water chemical maintenance:

Intex pool liner is sensitive to chemical disproportion or addition. Even with the industrial coating material used to make it stronger, chemicals with strong chlorine, muriatic acid, hypochlorous acid, or even cyanuric acid levels might bleach or wrinkle the pool liners.

You are advised to ask for recommendations for the best pool chemical type you should purchase, maybe from your pool store experts or check reviews online. But for chlorine, sodium hypochlorite-based products are much tender to the pool.

 

You need to also check your chemical level weekly and add the required chemicals according to your test results. Algae bloom will also swimmers and make the water condition worse. Pay attention to all your chemical compositions and you will have a more elongated pool lifespan.

 

Filtration and backwashing:

Every swimming pool is vulnerable to debris, dirt, and built algae or staining. Your filtration system entails your pool pump, main drain, skimmer, filter valves, return jets, and others in the same category. You need to run your filters daily to maintain clear water.

 

Backwashing is targeted at removing clogged particles in the swimming pool Filtration systems. Many swimming pool owners don’t backwash their pools until they notice the filters aren’t working up to the required rate.

 

Regular observation of pool Filtration system:

While you might be filtering and backwashing your pool as required, you also need to observe the working patterns, sound, and amount of time used to complete a task.

When you notice it is off the normal pattern, check the components. This will limit discovery faults when the filtration system is already damaged beyond simple solutions.

 

Limiting debris from entering:

Intex pool needs shielding from environmental contributors of debris. You should install your Intex pool in a position in your yard where it is free from leaves released from grasses, trees, or even vulnerable to a wind storm.

You can also purchase a pool cover to put over your Intex pool when not in the pool. When there are massive debris conditions, filter, vacuum, and check the pool’s chemical composition.

 

Conclusion

Now that you know how to patch an Intex pool ring, you may want to consider getting another pool. But if you love your old in-ground pool, you can fix it to keep using it for years.

With a few tools, patience, and some glue, you can get your liner back to its original state in no time. Did this tutorial help you? If so, please vote for us below! We would greatly appreciate it!

Leave a Comment